Mxl DRK Manuel d'utilisateur télécharger pdf (Page 2)

1. On the microphone clip, you’ll find an adjustment for angling the position

of the microphone. Adjust the clip so that the “cup” of the microphone

clip is facing upward.

2. Holding the microphone securely in one hand, place the microphone into

the “cup” portion of the microphone clip and then tighten the knurled ring

back onto the base of the microphone. Your microphone is now sup

ported by the microphone stand.

Attaching the XLR Cable

Your XLR cable has different connectors on each end. One end has three small

prongs (male), while the other has three small holes (female).

1. Begin by attaching the female end of the XLR cable to the base of the

microphone by aligning the notches (one notch each for the microphone

and the cable). The cable will fit snugly into place. To remove the cable,

press and hold the release switch on the cable’s connector.

2. If you are connecting your microphone into the XLR connector of a

microphone preamplifier or the input channel of a mixer, the other

end of the XLR cable will patch directly into the external device and you

will be ready to begin.

Using Your Microphone with a Computer

Most computers use what is known as a 3.5mm mini jack for audio input and

output. To connect your microphone to a computer, you’ll need to use the

supplied XLR - 3.5mm Mini-Plug adapter cable.

With your XLR cable already attached to the microphone, connect the male

end of the XLR cable to the female (XLR) end of the adapter cable. The other

end of the cable will have a 3.5mm connector. You are now ready to connect

to the computer’s audio input.

Many self-contained personal recording systems use ¼-inch inputs. Others have

both ¼-inch and XLR inputs. If the external device has XLR connectors, you can

patch the microphone directly into the external unit by using the supplied XLR

cable. If the external device uses ¼-inch inputs, you’ll need to use the supplied

XLR to Mini-Plug Adapter Cable with the 3.5mm to ¼-inch Adapter.

1. Connect your microphone and XLR cable to the XLR to Mini-Plug

Adapter Cable as previously described.

2. Plug the 3.5mm mini jack into the supplied 3.5mm to ¼-inch adapter.

You are now ready to use your microphone with ¼-inch input-equipped

Unpack Your Microphone

Begin by removing the contents of your

MXL Recording Kit.

You should have the following components:

• Self-Powered Microphone

• Desktop Stand

• Microphone Clip (this holds the microphone)

• XLR cable (this is the cable with 3-prong connections on each end)

• XLR to Mini-Plug Adapter Cable (this cable enables you to patch into your computer)

• 3.5mm Mini-Plug to ¼-inch adapter

• 9-Volt battery

Preparing the Microphone Stand and Clip

1. Open the desktop microphone stand so the tripod is fully open and

standing upright.

2. Take the microphone clip and screw it onto the microphone stand’s

threaded mount.

Setting Up Your Microphone

1. Holding the microphone securely in one hand, unscrew and remove the

knurled ring at the base of the microphone.

2. Now unscrew and remove the sloped ring around the base of the

microphone’s body. The microphone’s tubular body will now be loose.

3. Prior to removing the microphone’s main body housing, take a few mo

ments to visually orient yourself to the position of the battery switch rela

tive to the On/Off\ markings on the microphone’s body. Now carefully

remove the main body housing.

4. On the opposite side of the microphone from the On/Off switch, you’ll see

the housing that holds the 9-volt battery. The battery can only be inserted

one way - so don’t worry!

5. Place the battery (terminals first) into the battery housing and slide it

down and into position. The battery will “snap” into place when fully

inserted. If the battery doesn’t seem to fit, flip it over and re-insert it into

the housing.

6. Carefully replace the microphone’s main body housing - aligning the

On/Off markings with the microphone’s battery switch.

7. Next, re-install the sloped ring onto the base of the microphone. The

microphone’s body parts will now be secure and the On/Off switch

should move freely between the two positions.

Congratulations on your purchase of your MXL Recording Kit.

MXL microphones are the result of world-class engineering and man-

facturing capabilities. They are designed to provide you with outstand-

ing peformance and exceptional value. To help you get started, please

take a few moments to review the following instructions for setting up

your new microphone.

Configuring Your New MXL Microphone Placing the Microphone on the Desktop Stand

Using Your Microphone with ¼ -inch Input - Equipped Devices

Using Your Self-Powered Microphone with Phantom Power

Your self-powered MXL microphone can be used with phantom power without fear of damag-

ing either the microphone or the phantom power source. If the microphone senses phantom

power, it will automatically bypass the internal battery and operate using phantom power.

Please turn the microphone to the off position when not in use and remove the battery

when storing or not using the microphone for long periods of time.

devices.

1 2

DRK Users Manual 1

Commentaires sur ces manuels

Pas de commentaire

Mxl DRK Manuel d'utilisateur Page 2

Commentaires sur ces manuels

Produits connexes et manuels pour Microphones Mxl DRK